Of all the numbers on a tube drawing, the wall thickness is the one most often treated as an afterthought. The diameter and the radius get the attention, and the wall is copied from whatever the designer had in the catalog. Yet the wall is half of the ratio that decides how hard the bend is. A tube of 50 mm diameter with a 5 mm wall and one with a 1 mm wall are different jobs entirely, and the tooling, the machine and the scrap rate all follow from the difference.
This article treats tube bending wall thickness as a design and purchasing question. It keeps to numbers that a buyer can check against a drawing. It explains the wall factor, shows how to work out how much wall is left after a bend and what starting wall to order, covers thin wall and heavy wall in turn, and links the wall to machine ratings using Telhoo’s published data. The geometry of the radius is in centerline radius explained for tube bending, and the defects that follow from a wrong wall are in tube bending defects and what causes each one.

The Wall Factor and Why It Matters
The wall factor is the outside diameter divided by the wall thickness, and it is the first number to work out for any tube bending wall thickness question. A 50.8 mm tube with a 1.5 mm wall has a wall factor of 33.9, and the same tube with a 5 mm wall has a factor of 10.2. The higher the number, the thinner the wall relative to the diameter and the harder the tube is to support. Below about 20 a tube holds its own shape through a bend. Above about 30 it cannot, and it needs internal support. Above about 40 it behaves like thin sheet rolled into a circle.
The second ratio is the radius ratio, the centerline radius divided by the outside diameter, which UK and Australian drawings call the centreline radius ratio. The two ratios work together. A heavy wall can take a tight radius, and a thin wall needs a generous one or heavy tooling support. The practical starting points are set out in the table. They are industry guidance and not guarantees, and the boundaries move with the material and with how much ovality the drawing allows.
| Wall factor | Radius ratio | Usual support | Main risk |
|---|---|---|---|
| Under 20 | 3D and above | Bend, clamp and pressure die only | Springback and angle accuracy |
| 20 to 30 | 2D to 3D | Plug or single ball mandrel | Ovality starting to appear |
| 30 to 40 | 1.5D to 2D | Multi-ball mandrel and wiper die | Inside wrinkling and outside thinning |
| Over 40 | Under 1.5D | Multi-ball mandrel, wiper die, following pressure die | The part may not be formable |
The mandrel choices are described in types of mandrels for tube bending and how to select one, and the tooling set that goes with them in tube bending tooling and how to match a die set to the job.
How Much Wall Is Left After the Bend, Wall Thinning in Numbers
The outside of a bend stretches and thins. A first estimate of the thinning is 100 ÷ (2 × CLR/OD + 1) percent. It depends only on the radius ratio and not on the wall itself. At 1.5D it is 25%, at 2D it is 20%, at 2.5D it is 16.7%, at 3D it is 14.3% and at 4D it is 11.1%. It is a ceiling and not a prediction. A following pressure die and a well-fitted mandrel feed material into the bend and bring the real figure below it.
The remaining wall is the starting wall times one minus the thinning. The table shows what is left from three starting walls at four radii, using the estimate as a worst case.
| Starting wall | Left at 1.5D (25%) | Left at 2D (20%) | Left at 3D (14.3%) | Left at 4D (11.1%) |
|---|---|---|---|---|
| 1.5 mm | 1.13 mm | 1.20 mm | 1.29 mm | 1.33 mm |
| 2.0 mm | 1.50 mm | 1.60 mm | 1.71 mm | 1.78 mm |
| 3.0 mm | 2.25 mm | 2.40 mm | 2.57 mm | 2.67 mm |
Read it as a design tool. If the application needs at least 1.8 mm of wall left on the outside of every bend, the starting wall must be larger than 1.8 mm by enough to cover the thinning. At 2D the starting wall must be at least 1.8 ÷ 0.8, which is 2.25 mm. At 3D it must be at least 1.8 ÷ 0.857, which is about 2.1 mm. At 1.5D it must be 2.4 mm. The same requirement thus costs a thicker tube as the radius tightens, and a larger radius is often the cheapest way to meet a minimum wall.

Specifying Wall Thickness on a Drawing
A drawing should say what wall is wanted after the bend, and not only the wall of the tube before it. Write a minimum remaining wall at the outside of the bend, or a maximum thinning as a percentage, and say where it is measured. If the part is under a pressure code, the code sets the limit and the limit belongs on the drawing. Power construction, boiler, bridge, shipbuilding and process piping rules all set a minimum wall after forming, and the correct way to meet them is to work back from the limit to the radius and the starting wall, as in the example above.
Furniture, fitness and decorative parts usually have no such code, but the wall still matters for strength and for the surface. A frame designed to the nominal wall has quietly lost its margin at the outside of every bend, and the outside of a bend is often the highest-stress location. A design wall that already allows for the loss avoids the surprise. The standards side of the radius choice is in tube bend radius standards and how to choose a radius.
Wall Tolerance and What It Does
The wall on the drawing is a nominal figure, and the tube arrives with a tolerance. A tube bought at the low end of its tolerance has less wall than the drawing assumes, and a tube at the high end has more. The difference changes the thinning result, the mandrel fit and the force. A proven job can become marginal when a new lot arrives at the low end of the wall tolerance, which is one of the commonest causes of a defect that appears overnight.
The practical steps are simple. Order tube to a wall tolerance you can live with, and say so in the purchase order. Measure the actual wall and bore on a sample from each lot. Set the thinning budget from the minimum wall, and not the nominal. And keep the lot number with the proven settings. Welded tube can also carry an internal bead and a wall that varies around the section, and butted tube has a wall that varies along its length, so the position of the bend relative to the thick and thin zones can matter.
Thin Wall Tube Bending and the Wall Factor
Thin wall tube is the demanding end of the range. Its strength to resist collapse is low and it flattens when bent unless it is supported, and the inner wall wrinkles unless the gap at the inside tangent is filled. The tools that do this work are the mandrel and the wiper die. A ball mandrel supports the bore through the arc, and the number of balls rises as the wall thins and the radius tightens. A wiper die with a near-zero gap at the tangent stops the inner wall folding. A following pressure die feeds material into the bend and reduces the thinning on the outside.
Settings matter more as the wall gets thinner. The clamp has to grip without crushing the section, so a longer clamp die is better than more pressure. The mandrel nose position has to be right to a millimeter, because too far back leaves the start of the arc unsupported and too far forward drives thinning and humping. Lubrication has to reach the inside of the tube, because drag is highest where the mandrel is tight in thin wall. And the bend speed should be chosen for quality and not for speed, since a thin wall gives little tolerance for a rushed bend.
Thin wall is also where the choice of tube matters most, and tube bending wall thickness tolerance matters most with it. Tube with a consistent wall and a clean bore bends well, and tube with scatter or burrs does not. Mandrel exhaust tubing is the classic example, with high wall factors and tight radii, as covered in mandrel exhaust tube bending and what the part demands. For stainless, the extra points are in bending stainless steel tubing and what changes.
Heavy Wall Tube Bending
Heavy wall tube is the opposite problem. The tube holds its own shape and ovality and wrinkling are rarely the worry, and the difficulty is force. Bending torque rises with wall and with diameter, and a heavy section needs a heavy frame, a strong clamp and a large hydraulic unit. It is also slow. A thick section needs time to form without collapsing, so the bend speed falls as the wall rises, and the heavy-wall machines in Telhoo’s range are the slowest.
The published data shows the pattern. The 130NC takes Φ130 × 8 mm mild steel at 12°/s, and the 168NC takes Φ168 × 14 mm at 4°/s. The 168CNC takes Φ168 × 15 mm at 8°/s, with a 12 tonne frame and a 30 kW hydraulic unit, and the 219CNC takes Φ219 × 20 mm with an 18 tonne frame and a 45 kW hydraulic unit. At these sizes the cycle is dominated by loading and not by bending, since a Φ168 × 15 mm steel pipe weighs around 57 kg per meter. Springback is also worth care, since heavy sections release a lot of stored energy and variation between lots can move the result.
Measuring Wall Thickness After Bending
The wall thinning on the outside of a bend cannot be seen, so it has to be measured. The usual methods are an ultrasonic thickness gauge along the outside of the bend, a ball micrometer on a sectioned first article, and for critical parts a coordinate measuring machine or a sectioned sample under a measuring microscope. Take readings at the tangent points and at about 45° and 90° through the arc, because the minimum is rarely at the midpoint, and report the remaining wall in millimeters and as a percentage lost, since acceptance criteria are written both ways.
Measure the first article of every new part number, and again after any tooling change or new lot of tube. Record the results with the radius, the tooling set and the lot. Over time the records show how much real thinning a given setup gives against the geometric estimate, which is usually lower, and they give the evidence needed to approve a tighter radius or a thinner starting wall next time. Without the record, every job starts from the worst case.
Wall Thickness and Ovality
The wall also decides how much the section flattens. A thin wall has little resistance to collapse, so ovality rises as the wall factor rises, and the mandrel, the pressure die and the fit of the die cavity have to work harder to hold the section round. Ovality is measured as the spread between the maximum and minimum diameter over the nominal at a station in the bend. The acceptable value depends on the part, and a bend near a fitting or a seal is held tighter than one in the middle of a straight run.
For a given radius, a heavier wall nearly always reduces ovality, and it is one of the simplest ways to meet a tight ovality limit. The cost is weight and material, and the machine needs more force. If a drawing asks for both a thin wall and a tight ovality limit, ask whether either can be relaxed, since asking for both at once is what pushes a part toward the edge of what any tooling can do.
The Inside of the Bend, Thickening and Wrinkles
While the outside thins, the inside of the bend compresses and the wall thickens a little. In heavy wall tube that is harmless, and the thicker inside wall helps hold the section. In thin wall tube the compressed material tends to buckle instead of thickening, and the result is wrinkles that start at the tangent point. The wiper die and the mandrel exist to stop that, and the wall factor is the predictor of whether they are needed.
When wrinkles appear on the inside of a thin wall bend, the likely causes are a worn or badly fitted wiper die, a mandrel nose set too far back, too little following pressure die feed, or a radius too tight for that wall. The order in which to check them is covered in the defects article. The important point for wall selection is that a thicker wall moves the problem a long way, since a wall factor of 20 almost never wrinkles and a wall factor of 40 almost always needs a wiper die.
Choosing a Wall for Common Applications
Different applications settle on different walls, and the reasons are mostly about the loads and the finish. The table gives the direction and not the numbers, since the right wall depends on the design.
| Application | Wall tendency | What drives it |
|---|---|---|
| Furniture and decorative frames | Thin | Weight and cost, with a surface that shows every defect |
| Fitness equipment | Thin to medium | Dynamic loads, so the outside wall after bending matters |
| Exhaust systems | Thin | Weight and cost, with tight radii and a functional bore |
| Structural frames and guards | Medium | Stiffness and welding |
| Boiler and process piping | Medium to heavy | Pressure codes and a set minimum wall |
| Marine and heavy pipework | Heavy | Pressure, corrosion allowance and force |
Each row has a different cost of being wrong. In furniture a thin wall that wrinkles is a rejected part. In fitness equipment a wall that has thinned too far is a safety question. In piping it is a code question. The applications are compared in tube bending applications by industry and what each needs.
Material and Wall Together
The material changes what a given wall can do. A soft metal such as annealed copper or soft aluminum thins gracefully and ovalizes, so the wall matters mainly for roundness and for marks. A hard aluminum temper may crack on the outside before it thins much. Stainless work-hardens and needs a stronger frame for the same wall, and its published rating is lower than mild steel, as the 168NC pair shows. Carbon steel is the forgiving baseline.
If you are changing the material, recheck the wall. A part proven in mild steel at a given wall may need a different wall, radius or tooling in stainless or aluminum, and the rating of the machine may change. The comparison is in aluminum tube bending and how tube metals compare. And since springback also depends on wall, the correction has to be proven again, as in springback compensation tube bending and how to prove it.
Tube Bending Wall Thickness and Machine Rating
Every bender is rated for a diameter and a wall together, because both set the torque. A machine rated for a thick wall at a diameter is not necessarily rated for the same wall at a larger diameter. The table lists the published maximum tube in mild steel for Telhoo’s NC and CNC ranges, with the wall in the second column. Stainless is rated lower in the same machine, as the 168NC pair shows, with Φ168 × 14 mm in mild steel and Φ135 × 10 mm in stainless.
| Model | Maximum tube, mild steel | Maximum wall |
|---|---|---|
| 38NC, 38CNC | Φ38.1 × 2 mm | 2 mm |
| 50NC | Φ50.8 × 2 mm | 2 mm |
| 63NC, 63CNC | Φ63.5 × 2.5 mm | 2.5 mm |
| 75NC, 75CNC | Φ76.2 × 3 mm | 3 mm |
| 89NC, 89CNC | Φ88.9 × 3 mm | 3 mm |
| 115NC, 115CNC | Φ115 × 6 mm | 6 mm |
| 130NC, 130CNC | Φ130 × 8 mm | 8 mm |
| 168NC | Φ168 × 14 mm | 14 mm |
| 168CNC | Φ168 × 15 mm | 15 mm |
| 219NC, 219CNC | Φ219 × 20 mm | 20 mm |
Read the table by the jump in wall. The wall rating climbs slowly through the small sizes, then steps up sharply at the 115 class and again at the 168 class. That is where the frame, the drive and the loading change character. Where your wall sits near a step, check the rating in your material and at your radius before ordering, and ask what radius the published rating assumes. The selection sequence is in how to choose a tube bender from the part drawing.

An Example Across Three Walls
This example is illustrative and is not a customer drawing. A frame maker bends 38.1 mm tube on a 76.2 mm centerline radius, a 2D bend, in three walls, and wants at least 1.5 mm left on the outside.
With a 1.2 mm wall the wall factor is 31.8, and the thinning estimate at 2D is 20%, which leaves about 0.96 mm, so the requirement is not met and the part needs a thicker tube or a larger radius. With a 1.5 mm wall the factor is 25.4 and about 1.2 mm is left, which is still short. With a 2.0 mm wall the factor is 19.05, about 1.6 mm is left, and the requirement is met, with no mandrel or at most a plug on a stiff material. A 3D radius would bring the estimate to 14.3% and leave about 1.29 mm on the 1.5 mm wall, which is still short, and the real answer is a 2.0 mm tube.
The example shows the logic. Start from the minimum wall, work out the thinning, choose the starting wall or the radius, then check the wall factor for the tooling. It takes a few minutes with a calculator, and it prevents ordering the wrong tube. The same method works for any tube bending wall thickness question, whatever the material or the industry.
What to Send About the Wall
- The nominal wall and the tolerance you can hold in purchasing, and the material and temper.
- The minimum wall wanted after bending, and where it is measured.
- Every centerline radius on the part, and whether the design can open any of them.
- Whether the tube is welded or drawn, since a bead or a varying wall changes the choice.
- The ovality limit and any pressure or fatigue code that applies.
- Batch size and variants, since a stored program and proven tooling are worth most on repeat work.
Send those and the reply can say whether the wall works at your radius, which mandrel and wiper it needs, and which machine class carries it. Tell us about the part, and see the ranges on the CNC automatic pipe bending machine and NC semi-automatic tube bender pages.







